Menú

Adesivix 20

C2E Tile Adhesive

High performance cement adhesive (C2) composed by selected granulomentry silicate sands, redisperdible synthetic polymers and reological addicitives which allows prolonged open time (E) and C2E class high thyxotropy. Due to the elevated mechanical resistance, flexibility, adhesion and workability, can be used for both indoor and outdoor on plasters, cured and dry screeds, vertical and horizontal surfaces and surfaces subject to prolonged water contact such as pools or terraces.


Information

Fields of application

For floor and wall application of:

  • Ceramic tiles (gres, klinker, single-firing, double-firing etc.)
  • Mosaic of any type
  • Stone material, even large formats and overlapped

On cement supports such as:

  • Traditional plasters
  • Cured cement screed
  • Heating Floors
  • Waterproofing coatings such as CemPlast or MonoPlast

On pre-existent ceramic or marble floors it is recommended to de-wax in advance. Gypsum or plasterboard surfaces must be treated in advance with IsoPlast 581. See technical sheet for application on Anhydrite screeds.

Support preparation

Surface must be plain, stable, solid, free from dust and dirt. Supports must be cured and dry, not subject to shrinking after the application of tiles. Recover excessive gaps with a smoother (RasaPro) or self-levelling plasters (Level floor). In the presence of rising damp treat in advance with proper primers (Primer Bv 2K).

On excessively hot surfaces due to sun exposure, it is recommended to wet the surfaces with water, avoiding superficial stagnations.

In case of overlapping on very smooth or glossy ceramic, it is recommended to rough the surface to ensure adhesion. On pre-existent floors de-wax first. Gypsum or plasterboard surfaces must be treated in advance with IsoPlast 581. See technical sheet for application on Anhydrite screeds.

Mixture preparation

Pour in a container about ¾ of the necessary water to mix a bag of Adesivix 20, add gradually the powder and mix with a low-rounds stirrer. Proceed by adding the remaining water until an even, clump-free mixture is achieved. Let rest for 5-10 minutes and mix briefly before usage.

Tiling application

Apply a thin glue coating with the smooth side of the spatula, pushing vigorously against the support and immediately apply the mixture with a saw-tooth spatula (using the correct size, depending from the size of the tile). During application make sure the adhesive did not form a superficial film. Do not wet the glue after application, as the water may form an anti-adhesive film. Accurately beat the tiles to allow perfect adhesion. With outdoor extruded materials or in overlapping with size exceeding 25X25 cm, it is recommended to apply a double application (both on support and tile).

Reccomendations

It is recommended to mix with clean, non-brackish water. Do not add bonding agents, inerts or other materials. In the presence of high temperatures or dusty supports wet the surface in advance with water. Sun and wind exposure may cause the rapid formation of a superficial film. Described times shortens in hot environments and prolongs in cold environments. Apply between +5°C and +35°C. Do not apply on concrete surfaces subject to noticeable shrinking or shocks. Do not apply on heating floors or metallic surfaces.

specification item

Adesivo cementizio polimero modificato ad alta resistenza classificato C2E in conformità alla norma EN 12004 con tempo aperto prolungato (E) ed elevata tixotropia. Impiegato per interni ed esterni su intonaci, massetti stagionati ed asciutti, superfici verticali ed orizzontali e su superfici sottoposte a continuo contatto con acqua come piscine o terrazze.

Compliance

Technical Data

Application

notched trowel

Packs

kg 25

Colour

white - grey

Consistency

powder

Mixing water

approx. 7-8 l per bag

Consumption

mosaics and small sizes tiles: 2-2.5 kg/sqm; normal sizes tiles: 3-5 kg/sqm

Grain size

≤ 0.6 mm

Initial tensile adhesion strength

≥ 1 N/mm² - EN 1348

Tensile adhesion strength after water immersion

≥ 1 N/mm² - EN 1348

Tensile adhesion strength after freeze thaw cycles

≥ 1 N/mm² - EN 1348

Tensile adhesion strength after heat ageing

≥ 1 N/mm² - EN 1348

Bulk density

1.7 kg/dm³

Application temperature

from +5°C to +35°C

pot life

approx. 6-8 hr

Mix standing times

approx. 5-10 min

Open time

20 min - EN 1346

Adjustability time

approx. 40 min

Ready for use

after 14 days

Set to light foot traffic

after 24 hr

Waiting time before grouting

wall joints after 12 hr - floor joints after 24 hr

Reaction to fire

EuroClass A1 - UNI EN 13501-1

Tools cleaning

water soon after use

Pallet

60 bags of kg 25

Data contained in technical data sheets refer to laboratory tests. Indications and methods may be subject to change over time, depending on any technological and productive improvements. Products application takes place out of our control, as we cannot directly intervene on the conditions of the construction sites and on the execution of the works. All indications are general and do not bind our company in any way and therefore the responsibility falls exclusively on customer. We recommend a preventive test of the product in order to verify the suitability in relation to its particular use. Technical service is available to provide additional information.

Do you want to know how many Adesivix 20 packs you need?

Calculate it now

surface to be covered in square meters